Although toilet leaks shouldn’t be a cause for concern, it is not something to worry about. However, no one likes going into the bathroom wearing dry socks and then coming out of there with wet socks. Most toilets with a leaky base can be fixed easily using these DIY steps. This guide will help you quickly fix your toilet leak. It will tell you the causes, what tools you’ll require, how to fix it, and tips for preventing future leaks.

Four Reasons Toilets Leak at Base

These are the possible reasons your base might be leaking.

You must tighten the Tee Bolts.

Two bolts, called tee bolts, hold the toilet’s base to the ground. The toilet may rock if these bolts become loose, and the wax ring seal will break. If your tee bolts have become loose, water could seep from the toilet’s base every time you flush it.

It is time to replace the wax ring.

Because the toilet is not flushed, it’s common to need to replace the wax ring. Another reason why a wax-ring might need to be replaced may be that it has become hardened over time and is no longer flexible. The seal may also be damaged. It allows water to seep into the base.

There is a loose water supply line.

You’ll notice a leaky water supply line if your toilet is not flushed every time it’s used. Make sure to inspect the connection between the tank’s supply line and the tank to ensure that the rubber seal and nut are in place.

Water is condensing on the toilet and dripping down.

The porcelain and water in the toilet bowl and tank are usually quite cold. You’ll see water pooling at your toilet’s base if you have a humid environment. Once you have identified the source of the problem, you can get the tools necessary to repair the toilet.

The Tools and Supplies You Will Need To Stop Your Toilet from Leaking

These are the most important supplies that you will need to fix a leaking toilet.


To remove the bolts and nuts that hold your toilet closed to the ground, you will need a wrench. The wrench should be open-ended.


Depending on your toilet, you might need a set or screwdrivers to remove various parts of the toilet and repair it.

Bathroom cleaner

You should clean the area around your toilet with an anti-bacterial bathroom cleaner. This will ensure that you clean up any leaking water.

Clean Cloths

To complete this project, make sure you have several cleaning cloths. Microfiber towels and Terry cloth are the best.

Washers, Gaskets and Toilet Bolts. Toilet Wax Rings.

A toilet repair kit is required. It includes all the necessary tools and supplies. You can also buy washers, bolts, and other parts individually if you wish.

Cordless drill or driver

It may be difficult for some nuts and bolts to be removed manually. To make tight bolts more accessible, use a power tool such as a cordless drill.


Bolts can be stripped or corroded. A hacksaw can be a great tool to reduce frustrations when trying to remove corroded bolts. You can use the hacksaw to remove bolts from the base of the toilet, plastic bolts on the seat, and any other bolts.

Rubber gloves

It can be messy to fix a toilet base leak. To protect your hands, make sure you have gloves.


Caulking is necessary to reseal the toilet’s edges. You have all the tools and materials you need to stop your toilet from leaking.

How to stop your toilet from leaking around the base

These steps will help you fix your toilet leak.

1. Check For Condensation.

To make sure your toilet problem isn’t condensation, inspect the toilet bowl from the outside. These tips can help prevent condensation from causing the problem.

  • Place a tray.
  • Insulate your water tank
  • Check that your flapper isn’t damaged.
  • Use shorter, cooler showers and then turn on the fan.

Continue to search for the root cause of the problem if this is the case.

2. Tend to tighten the Tee Bolts.

Take off the plastic covers on the toilet’s base from both sides. To tighten the tee bolts, use an adjustable open-end wrench. To ensure that the wax ring sealing the toilet drain outlet is compressed, tighten the toilet against the flooring. You may have to take out the toilet and reinstall it if the tee bolts are not tight enough.

3. Disconnect the toilet and take it out.

Before you start disconnecting the toilet, turn off the water supply. The shutoff valve can be found on the left side, near the water supply tube tailpiece and the water valve tailpiece.

  • To drain the toilet tank and water, flush it. To drain excess water from the bowl and tank, use a sponge or cloth.
  • Next, take a screwdriver and unscrew the bolt that connects the supply tube to fill valve tailpiece.
  • You can remove the nuts at the base the toilet by using your wrench. If the bolts won’t turn or are corroded, you may have to use a hacksaw.
  • Lift the toilet up from the floor drain. You may find it easier to hire someone to help you move the toilet.
  • To prevent any damage, place the toilet on its side.

4. Take out the wax ring and install a new one.

Use a putty knife to remove any old wax around the drain opening. Be sure to get rid of all the wax. Once all the putty has been removed, you can install the wax ring. Place the ring with the plastic cone facing toward the drain. Place the tee bolts correctly in the key holes on either side of the drain.

5. Reinstall the toilet.

The toilet should be lifted carefully and placed back over the drain to allow the tee bolts to pass through the holes at the base. To create a seal, press the toilet onto the wax ring.

Use a wrench to tighten the tee bolts or nuts. Over-tightening them could cause cracking in the porcelain.

6. Connect the Water Line

Turn the water on again by connecting the water supply tube to fill valve. After the toilet tank has filled back up, flush the toilet and inspect for leaks. After you have made sure that there are no leaks, seal the toilet base with caulk.

How to prevent future toilet leaks

These five tips will help you prevent leaks from happening in your toilet.

Get rid of leaky toilets immediately.

Do not wait for your toilet to leak before you repair it. To prevent any future leakage, you must keep up with your toilet’s maintenance. You can save money by fixing the leaky toilet immediately.

You should not flush anything other than human waste and toilet paper.

Toilet paper doesn’t break down like toilet paper, so it’s important to not flush items in the toilet. A clogged pipe can lead to more than a small leak at the base of your toilet.

Do not use chemical drain cleaners to unclog your toilet.

To flush down the toilet, chemical drain cleaners can be too harsh. These cleaners can cause damage to pipes and fixtures.

Each six months, inspect the components of your toilet.

To avoid unexpected toilet problems, make sure that your toilet components function properly at least twice per year. This proactive approach will allow you to fix small problems before they become major problems.

If you need a plumber, hire one.

You may not be able to fix all the problems with your toilet plumbing. Calling a professional Long Beach Plumber relieves you of all worries regarding plumbing repairs.

A professional Long Beach Plumber will fix your toilet leak right the first time. It is important to address common plumbing issues, such as a toilet that leaks at the base, so you can avoid bigger plumbing problems later.