Your home’s plumbing system is a feat of ingenuity. It was developed over the past five-thousand year, starting in ancient Greece. It was an engineering marvel to be able to bring water from distant mountains into Rome during the Roman period.The beginning of plumbing as we know today was in the 1800s, when New York City installed its first water main. It was initially used for firefighting.

Leakages can occur at any point in any plumbing system.

As we use these appliances every day, leaky faucets, showerheads and toilets can be easily detected.

Water leakage from the supply lines, under sinks, drains, and sewer lines must all be fixed before they cause damage to your home. Because of their location, these leaks can often go unnoticed and remain hidden for long periods.

How much water is wasted every day by a leak?

The severity of the leak and the number of outdoor hosebibbs or toilets leaking will determine how much water you waste. Let’s take, for example, two faucets that leak at 10 drips per hour.

These two fixtures can waste nearly 30,000 drips per daily, which equates to almost 700 gallons per year.

You should feel guilt about all the water wasted. However, leaks can also lead to higher bills. Even small leaks can cost you $20 to $30 per month in water bills. This may seem like a small amount, but it adds up to $360 over a year.

How do I know if there is a leak?

A homeowner’s water bill that is higher than the average will be their first sign of a leak. A bill will include a chart that shows your water usage over the past few months. An abrupt spike in water use can indicate a leakage in the water supply lines.

A leaking water supply pipe can cause reduced water pressure at multiple faucets or showerheads.

Leaking faucets and running toilets are obvious, but we still see them every day. It is crucial to find hidden leaks quickly to prevent water damage to your property or home. You should be aware of the signs that indicate a hidden leak in your home.

Where is my Leak Coming from?

It is difficult to pinpoint the source of a leaky pipe. This challenge applies not only to the homeowner but also to plumbers who aren’t as experienced. Long-term water leaks can cost thousands of dollars and cause damage that could last for years. It is important to locate the source of the leak quickly. Water damage from plumbing leaks is the most common claim against homeowners insurance policies.

Water Supply Lines: The water lines that supply your water are pressurized so that water flows to all homes in the neighborhood. The water supply to your home comes from one pipe. It is connected by a meter that measures usage. A pressure regulator regulates the water flow. A pressure regulator is a device used to reduce the pressure in your home’s water supply.

It would cause damage to your plumbing and fittings if it was allowed to enter your home under its unregulated pressure (100 lbs/square inch)

Water is normally brought into a house at a pressure of 30-50 psi. This is enough to supply water to a two- or 3-story home. A broken water supply line can still release hundreds of gallons per an hour to your home, even with the lower pressure.

Leakage detection for sink and bathtub faucets: Sometimes the most obvious leaks are often the most overlooked. A dripping faucet is something we “get used to”, and it’s possible that we forget to hear the sound it makes once it is fixed.

A dripping faucet is not considered a plumbing emergency. However, it’s important to address any leaks in your home immediately. Leaking faucets are difficult to repair and can result in water loss of hundreds of gallons each month. This will lead to higher bills.

Toilet Leaks: The bathroom is one of the most commonly used plumbing fixtures in your home. Leaks can occur both inside and out of the tank. Leakage can occur due to corrosion in the distribution valve and flexhose connection. This can lead to significant leaks and broken base flanges that can allow raw sewage to leak into your floors.

There are many moving parts inside the tank that can wear due to regular use, such as fill valves and handles.

The combination of hard water, chemicals and other substances can cause damage to other parts such as the rubber flapper that covers the toilet tank or the bowl. It doesn’t matter what the reason, these parts can wear and cause leaks.

Water Heater Leaks: Any leaks around the water heater should be alarming, especially if they are coming from the seam.

Leakage from a tank-type heater can indicate that it is about to fail. This could leave behind 40 to 70 gallons of water to clean up. Repairing this kind of water damage can often cost thousands of dollars.

What is the Growth Rate of Mold After a Leakage?

Mold is an fungus that grows anywhere there is excess moisture. It produces airborne spores which quickly reproduce. Mold growth can start within 24 hours of a leak starting and will continue until the leak is fixed.

Mold remediation is the process of removing and replacing contaminated surfaces in a home following water damage. This may involve replacing drywall, ceilings and studs depending on the extent of water damage.

What is the drying time for drywall?

We can only answer that question with “it doesn’t matter.” The drywall begins to lose its structural integrity when it is exposed to water. As the paper fibers that make up the drywall begin to dissolve, so does the drywall.

Dry sheetrock can retain moisture for many months. This makes it a great place to grow mildew or mold. Any drywall within 2 feet of water damage should be replaced.